Pneumatic & Hydraulic Parts

Air cylinders, solenoid valves, air compressors, pneumatic fittings, hydraulic cylinders, pumps, hoses and seals.

Pneumatic & Hydraulic Parts for Concrete Batching Plants

Quality replacement parts with factory-direct pricing. Contact us for a complete list.

Available Pneumatic & Hydraulic Parts

Part NameCommon MaterialSpecifications
Air CompressorsScrew type, quiet0.5 – 3 kW
Pneumatic CylindersAluminum / steel barrel32 – 125 mm bore
Solenoid Valves5/2, 5/3 way24V DC / 220V AC
Hydraulic PumpsGear typeFor silo systems
Air Filters & RegulatorsFRL unitsG1/4 – G1

How to Order the Right Parts

To ensure the correct fit, please provide us with:

  • Your mixer / plant model (e.g. HZS120, JS2000)
  • The part name and quantity needed
  • Photos or drawings of the worn part (if available)
  • Your plant's serial number or year of manufacture

Need a quote? Send us your plant model and part list — we respond within 4 hours with specifications, material options and factory pricing. WhatsApp: +86 187 6888 8850

Pneumatic & Hydraulic Parts FAQ

What size pneumatic cylinder do I need?

It depends on the application — baghouse doors, silo valves or discharge gates. Send us your current cylinder bore and stroke.

Do you supply complete FRL units?

Yes, we supply filter-regulator-lubricator units in sizes G1/4 to G1 for batching plant air systems.

Can you match solenoid valve voltage?

We stock 24V DC and 220V AC solenoid valves. Specify your control voltage when ordering.

How do I know if the seals in a pneumatic cylinder are gone rather than the valve?

Disconnect the rod-end air line and stroke the cylinder. If air escapes continuously from the open port, the piston seal is bypassing. If it is quiet, the cylinder is probably fine and the problem sits in the valve spool or the supply.

What air pressure should a batching plant air line hold?

Most plant pneumatics are designed around 0.6 to 0.8 MPa at the receiver. What matters more is pressure at the cylinder under load — a line that drops from 0.7 to 0.4 MPa when a gate strokes points at a restriction, not at the compressor.

Why do solenoid coils burn out?

Almost always a voltage mismatch, or a coil left energised continuously when it is rated for intermittent duty. Check the coil marking against the panel supply, and check whether the valve is being held open for hours at a time.

How often should the air receiver be drained?

Daily on a plant running two shifts, and after every shift in humid climates. Fit an automatic trap if nobody is going to remember — water carried into the valves is the single most common cause of premature failure we see.

WhatsApp Us Request Parts List

When the air system is the problem, not the valve

Most orders we ship for butterfly valves and silo gate cylinders turn out to be air-supply problems. The valve gets the blame because that is where the symptom shows — the gate creeps open, or it slams shut instead of easing down. Before you price a new actuator, put a gauge on the line and work backwards.

Three things cause roughly four out of five of these calls. First, water in the line. A compressor that runs hot carries moisture past the separator, and it collects in the lowest point — usually the filter-regulator bowl or a dead leg near the silo. The bowl fills, the diaphragm stiffens, and the cylinder gets a weak, spongy stroke. Second, a filter element nobody has changed. A choked element passes pressure at the gauge but not flow at the cylinder, so the valve moves slowly while your panel shows normal pressure. Third, a solenoid coil that is energising but not shifting the spool, because the coil voltage does not match the panel — a 24 V DC coil fed from a 220 V AC circuit will buzz for a week and then burn open.

Hydraulic discharge gates have their own logic. If the gate drifts down under a full hopper, the cylinder is usually fine and the relief valve is passing. If it holds but the pack runs hot, look at oil condition and the cooling path before the pump. Seal kits are cheap; pumps are not.

Diagnosing by symptom

SymptomWhat it usually isCheck this first
Valve moves slowly, gauge reads normalChoked filter element or crushed hoseFlow at the cylinder, not pressure at the tee
Gate creeps open on its ownSpool leakage or cylinder seal bypassCap the cylinder port and watch if it still drifts
Slam instead of soft closeFlow control valve closed or missingMetering screw on the exhaust side
Cylinder rod rusts or pitsMoisture in air, no dryerDrain interval and whether a dryer is fitted
Coil hot, no movementWrong voltage or failed coilCoil label against panel supply
Hydraulic pack overheatsRelief valve passing, oil degradedOil colour and relief setting

Matching the part without a model plate

A lot of plants in Africa and Central Asia were installed years ago and the nameplate on the cylinder is gone, painted over, or in a script nobody on site reads. You do not need the original part number — you need five measurements: bore, stroke, mounting style (foot, flange or clevis), rod thread, and port size. Send those with a photograph of the mounting and we can match it against what we hold for HZS and JS series plants.

For valves, the useful numbers are body size, connection standard, and whether the actuator is double-acting or spring-return. Spring-return matters on silo discharge: if air is lost, a spring-return valve fails closed and holds material, which is usually what you want. A double-acting valve with no air simply stays where it was, and a full silo gate that stays partly open is a spill waiting to happen.

HZSMOVE

We reply within 1 hour

👋 Hello! Welcome to HZSMOVE.

I'm here to help with your concrete batching plant relocation needs. Ask me anything!

Just now
Start Chat