Conveyor & Transport Parts
Conveyor belts, rollers, idlers, pulleys, belt cleaners, screw conveyor blades, and bucket elevator components.
Conveyor & Belt Parts for Concrete Batching Plants
Quality replacement parts with factory-direct pricing. Contact us for a complete list.
Available Conveyor & Belt Parts
| Part Name | Common Material | Specifications |
|---|---|---|
| Conveyor Belts | EP / NN rubber conveyor belt | B800 – B1200 |
| Idler Rollers | Steel, sealed bearing | B800 – B1200 |
| Belt Pulleys | Cast iron / steel | Drum, wing types |
| Tensioning Devices | Steel, screw type | All belt widths |
| Skirting Rubber | NR / SBR rubber | Standard profiles |
How to Order the Right Parts
To ensure the correct fit, please provide us with:
- Your mixer / plant model (e.g. HZS120, JS2000)
- The part name and quantity needed
- Photos or drawings of the worn part (if available)
- Your plant's serial number or year of manufacture
Need a quote? Send us your plant model and part list — we respond within 4 hours with specifications, material options and factory pricing. WhatsApp: +86 187 6888 8850
Conveyor & Belt Parts FAQ
What belt widths do you supply?
We supply EP and NN conveyor belts from B800 to B1200 for batching plant aggregate conveyors, with custom widths available on request.
Do you sell complete conveyor systems?
We sell replacement parts as well as complete aggregate conveyor systems for HZS plants. Contact us with your plant model.
Can you match belt length and splice type?
Yes, provide your belt length, width and required splice (mechanical or vulcanized) and we will supply an exact match.
Why does my conveyor belt run off to one side?
Pulley alignment first, then uneven take-up tension, then off-centre loading. Check them in that order and change one thing at a time — adjusting tension to fix an alignment problem usually makes the belt worse.
How do I stop the screw conveyor from blocking?
Look at the material before the machine. Wet sand, fibrous material or a partially blocked outlet will block a screw conveyor regardless of its condition. Also check flight wear — a worn flight conveys less and material accumulates.
How often should conveyor idlers be replaced?
Replace on condition, not on a fixed calendar. An idler that will not spin freely by hand, or that is noisy and hot after running, is on its way. Carry a few spares in the sizes used on your belts.
What causes skirt rubber to tear?
Usually being set too tight against the belt, so it wears or tears rather than deflecting, or being fitted with the wrong hardness for the material. Skirt rubber should make light contact and flex, not clamp the belt.
Belt tracking: three causes, in order
A belt that runs off to one side is the most common conveyor complaint and almost always one of three things. First, pulley alignment — the head and tail pulleys must be parallel to each other and square to the belt centreline, not merely tight. Second, take-up tension uneven between the two sides, which pulls the belt toward the slack side. Third, off-centre loading, which pushes the belt sideways every time a batch drops.
Work through them in that order and check one at a time. It is tempting to adjust the take-up first because it is easiest to reach, and that is how a small tracking problem becomes a belt with a permanent set. If the belt has already run off for a while, look at the edges — a frayed or curled edge will keep pulling the belt off no matter how well the pulleys are aligned.
Conveyor and screw conveyor faults
| Symptom | Likely cause | Fix |
|---|---|---|
| Belt runs off one side | Pulley misalignment or uneven tension | Square the pulleys first, then tension |
| Belt slips under load | Insufficient tension or worn lagging | Tension and drive pulley condition |
| Material spills at transfer point | Skirt rubber worn or set too tight | Replace skirt, set a light contact not a clamp |
| Screw conveyor blocks | Wet or fibrous material, or worn flight | Check material moisture and flight OD |
| Screw conveyor screams | Hanger bearing dry or failed | Grease interval and bearing condition |
| Idler seizes and belt wears through | Seal failure, dust ingress | Replace idler, check sealing type |
Screw conveyor wear happens in two places
The flight edges and the hanger bearing. Flight wear shows as a rounded, polished outer edge and a falling throughput that operators describe as the conveyor being slow. Once the flight OD has worn down, material stops being pushed efficiently and starts riding with the screw instead of along the trough. Check the flight diameter against a new one before assuming a drive problem.
Hanger bearings sit in the material stream and take the worst of it. A dry or seized hanger bearing turns the screw into a very effective pipe reamer — the symptom is a squeal that changes with load, followed quickly by a hole in the trough. Grease on the interval the manual gives, and more often on cement or damp sand duty.